Commercial · Overland Park, KS
For a concrete curb and gutter that controls runoff and protects pavement edges, the base and the pour matter as much as the finish. Quality Concrete Overland Park installs and replaces curb-and-gutter systems in Overland Park for driveways, parking lots, and private streets with grading, reinforcement, and clean tie-ins to existing asphalt or concrete.
We start with layout and elevations, then excavate to the required depth and width so water flows where it should. Subgrade is proof-rolled, soft spots are undercut, and we place and compact a 4-6 inch granular base (CA-6/AB-3 style aggregate) to reduce settlement and cracking. Forms are set on stringlines with consistent reveal, then we install rebar or dowels where needed, including doweling into existing slabs to prevent separation at transitions and returns. Before concrete arrives, we confirm slope, curb height, gutter pan width, and inlet locations so the curb line drains instead of trapping water.
Kansas freeze-thaw cycles, de-icing salts, and spring rains are hard on edges, so we use an air-entrained concrete mix and place it at the right slump for a dense, workable finish. Joints are not an afterthought, we tool control joints on a schedule that matches the run and include expansion joints at tie-ins, radii, and structures to manage movement. Finish options include broom-finish for traction on the gutter pan, clean tooled edges on the curb face, and consistent radii at corners and driveway openings. After placement we cure correctly (curing compound or wet cure as conditions require) to reduce surface checking and scaling, then we protect the work while it gains strength.
Overland Park customers choose us because we build curb-and-gutter runs that fit the site, not just the forms. We coordinate grades with your driveway, sidewalk, parking lot, or drainage plan, and we communicate clearly about access, staging, and timelines before the first cut is made. Crews show up with the right equipment for the job, including stringlines/laser level for elevations, vibrators for consolidation, and saws for clean cuts and removals. You get a licensed and insured contractor that provides a free written estimate and keeps the scope tight, so you know what is included and what it costs.
At the end of the job we walk the line with you and verify flow, tie-ins, joint locations, and overall appearance. We clean up spoils, haul away demolished concrete, and leave edges ready for backfill, topsoil, or asphalt patching, depending on the project. You receive clear guidance on cure time, traffic timing (foot and vehicle), and how to protect the curb face from early impact. The result is a concrete curb and gutter system that directs water, supports pavement edges, and looks uniform from start to finish.
Yes. We provide a free written estimate after an on-site evaluation so scope, prep, thickness, and finish are clearly defined.
Yes. We handle demolition, hauling, base correction, and replacement, including tying into adjacent slabs and matching grades for proper drainage.
We do both. If the slab is structurally sound, repair options may include crack repair, partial replacement, or correcting trip hazards, but widespread settlement or base failure typically calls for replacement.
Typical prep includes excavation to depth, compacted aggregate base, formwork, grade and slope setup, reinforcement placement, and planning for control joints and drainage.
Yes. Quality Concrete Overland Park is licensed and insured for residential and commercial concrete work.
A well-built concrete curb and gutter does more than look clean, it manages stormwater, protects asphalt edges, and defines lanes, islands, and driveway entrances. Quality Concrete Overland Park installs new curb-and-gutter runs and replaces failing sections for homes, HOAs, and commercial properties, focusing on correct elevations, stable base prep, and durable concrete placement that holds up to freeze-thaw and de-icing salts.
Concrete curb and gutter failures usually start below the surface. Settled subgrade, thin base, or poor drainage can lead to cracking, spalling, and ponding that undermines adjacent asphalt or concrete. Our process starts with grades and drainage, then excavation, undercutting soft spots, and compacted aggregate base. We set forms on stringlines and verify slope with a laser level so the gutter pan carries water to the right outlets instead of holding it along the curb line.
During placement we focus on consolidation and finishing details that extend service life. We use an air-entrained mix, place at a workable slump, and finish with a broom-finish where traction matters. Control joints are tooled or saw-cut to help manage shrinkage cracking, and we use expansion joints at tie-ins and structures to reduce random breaks. Curing is handled with the right method for weather conditions to limit surface scaling and early drying.
If you are planning a parking lot upgrade, driveway replacement, or drainage correction, curb-and-gutter work is the time to get elevations and transitions right. Share your goals and we will provide a clear scope, a written estimate, and a straightforward plan for protecting access during the work. When the job is complete, we walk the site with you, confirm drainage performance, and leave the area clean and ready for backfill or patching.
Call now or send a request and we will reach out within one business day to schedule your free, no-obligation estimate in Overland Park. We assess the project, review the details, and give you a written quote before any work starts, so you know exactly what to expect.
Prefer to write? Contact us or head back to the home page.